Call

 

The publisher is making several great annotation on the subject of How to Install a Bathtub Yourself overall in this post further down.

Mounting a bath tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is also a moderately hard task. If the old tub is readily obtainable, the task can relocate easily; if you need to open up a wall surface to eliminate the old bathtub and position the brand-new bath tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub and also embeded in the new one. See to it you have qualified on your own for the work and fit trying it. Rather than hiring a professional to take control of a halfway-completed job, it is far better to take into consideration using one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This article will certainly help you mount a brand-new bath tub in your bathroom if you have actually currently bought a new bathtub as well as do not require to transform the arrangement of your previous water pipelines.
Your tools and product list must make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome because of the limited accessibility that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will originate from the pipes. Once the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former kind ought to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Mounting the Bathtub

Utilizing the two wooden boards under its feet, position the tub in the required setting. The wood boards are practical in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the bath tub up until the level checks out level.
To set up faucets, fit the bottom of the outermost versatile faucet adapter to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water system and also check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bathtub as well as additionally inspect the overflow outlet and the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as explained in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the bathtub has been used at least when as this will resolve it into its last position.

 

 

Preparing for the Setup

Firstly, the sustaining structure provided with the bathroom should be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the flexible faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its final position.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, leading to issues with wetness and possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the tub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealer can split rather very early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the market. It is suggested to fit the tiles utilizing water-resistant or waterproof adhesive and grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

As a keen reader on Tools You Need to Install a New Bathtub , I figured sharing that piece of content was a good thing. I beg you set aside a second to distribute this entry if you enjoyed it. Many thanks for taking the time to read it.

Set Up An Appointment